24C128 DATASHEET PDF

24C Datasheet, 24C 16kbyte Serial SMD EEPROM Datasheet, buy 24CSMD. 24C FEATURES Extended Power Supply Voltage Single Vcc for Read and Programming (Vcc to V) Low Power (Isb @ V) Extended I²C Bus, 2-Wire. Product Support – Data sheets and errata, application notes and . Microchip products meet the specification contained in their particular Microchip Data Sheet .

Author: Samulabar Samugar
Country: Bermuda
Language: English (Spanish)
Genre: Sex
Published (Last): 11 June 2014
Pages: 332
PDF File Size: 6.27 Mb
ePub File Size: 5.53 Mb
ISBN: 852-3-81136-622-7
Downloads: 56043
Price: Free* [*Free Regsitration Required]
Uploader: Kehn

Especially, a common GND between: For example, in Table 8: Has anybody else encountered and fixed this problem? Then multiply 8 chips x 8 vatasheet each, which gives 64 pf. On the EEPROM, if you have the version that datahseet “chip enable” pins, then what voltage levels do you have these pins connected to?

So using the maximum sized pull-up resistor is basically a non-issue. What version of the CCS compiler do you have? So I can’t tell you if there was a problem for sure.

TOP Related Posts  LOU BALDIN PDF

The resistors should be connected as shown: That is the correct data sheet for a MBN6. So do that, and don’t add any capacitors.

All times are GMT – 6 Hours. If i use a 4k7 resistor i will need a 68pF capicitor as well?

24C128 Datasheet PDF

I am tring to use an ST M supplier catasheet calls it 24C external eeprom chip with the Fri Feb 28, 5: I don’t even have records for the Beta versions. Sat Mar 01, 1: But this is really a non-issue in most designs. Hope that CCS had the software i2c working with vs. The users were the Beta testers unknowingly, until they figured it out.

24C (ETC) PDF技术资料下载 24C 供应信息 IC Datasheet 数据表 (1/8 页)

GND, Vcc, or un-connected? If you had the chip that has 3 chip-enable lines, then it would be a “-BBN6”. It probably didn’t get out of “Beta” meaning excessingly buggy until version 3. If you had the chip: Send them to support ccsinfo. For pf, the largest resistor value can be 14K. Dwtasheet I can’t tell you if there was a problem: Fri Feb 28, 1: CCS does not monitor this forum on a regular basis.

TOP Related Posts  HOW DIGITAL DETECTIVES DECIPHERED STUXNET PDF

24C128 Datasheet

The resistors should be connected as shown in this schematic: You need a pull-up resistor on SDA: It doesn’t represent capacitors: The only reason you would want to use the largest possible resistor is if you have a low-power design, and your primary concern is conserving the battery.

Do you have proper connections to Vcc and GND, for both: It’s much better to go for signal integrity. Here’s the data sheet: It doesn’t represent datasjeet that you’re supposed to add. Or does anyone have any suggestions datxsheet to mistakes i may have made.

I might have that version at the company, and could test it on Monday, but I’m not sure. Especially, a common GND between the two chips. Don’t try using hardware i2c. Datasheey don’t add any.

Then you can refer to their graph in Figure 3, and see the maximum value of pull-up datwsheet that you can use. Fri Feb 28, 4: Fri Feb 28, 2: Add a few more pf for the output capacitance of the PIC pin that’s driving SDA, and maybe a few more pf for stray capacitance. Are you using ICD? But the chip will not initialise.