IEC SOUND SYSTEM EQUIPMENT –- PART 7: HEADPHONES AND EARPHONES. Buy IEC SOUND SYSTEM EQUIPMENT – PART 7: HEADPHONES AND EARPHONES from SAI Global. IEC Ed. Sound system equipment – Part 7: Headphones and earphones IEC (E), is applicable to headphones, headsets, earphones.
|Published (Last):||3 January 2005|
|PDF File Size:||4.42 Mb|
|ePub File Size:||17.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
You may experience issues viewing this site in Internet Explorer 9, 10 or Hardware Iecc In order to run the sequences, the following hardware is required: Take the smart route to manage medical device compliance.
Calibrate the microphones per the instructions in the SoundCheck manual. Headphone Voltage Sensitivity Final Display.
You may find similar items within these categories by selecting from the choices below:. A series of post-processing steps follow to apply the weighting and correction curves, calculate the LAEQ and then the Simulated Program Characteristic Voltage is calculated along with the Hz voltage sensitivity.
Setup System, Hardware and Calibration Before attempting to run any of the sequences, read the following setup instructions. Accept and continue Learn more about the cookies we use and how to change your settings. Headphones and Earphones is an international standard intended to characterize the performance of headphones and earphones. This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3.
There are several unique Signal Paths used in the sequences which are 60628 a part of the default SoundCheck installation. No – I don’t want to receive the latest audio test information by email.
BS EN 60268-7:2011
Marking, Microphones, Audio systems, Ratings, Designations, Instructions for use, Headphones, Classification systems, Frequency response, Earphones, Audio equipment, Voltage measurement, Impedance measurement, Testing conditions, Preamplifiers, Comparative tests, Acoustic measurement, Electrical wave measurement, Electrical properties and phenomena, Acoustic testing.
Crosstalk and radiation curves are then shown on the final display. Test Setup for measuring headphone voltage sensitivity. FebDecember 17, – 3: If passive, connect to the headphone amp or separate audio power amplifier You are ready to start the sequence. This sequence uses a pink noise stimulus to characterize the passive, active and total attenuation of noise cancelling headphones.
Your basket is empty.
The play and record acquisition takes place 3 times and the user is prompted to reposition the DUT on the HATS in between acquisitions. If more than 4 input channels are available, all input signal paths may be assigned to separate hardware channels.
It iev also be used to characterize the passive attenuation only of a standard non-ANC headphone. Find Similar Items This product falls into the following categories.
BS EN – Sound system equipment. Headphones and earphones
eic Software Requirements SoundCheck Matthew Miller November 15, – 6: It is recommended that the sequences be run directly from the IEC folder.
A pink noise stimulus is played from the noise speakers and recorded by the occluded ears. The folder contains dependent files required to run the sequences. Please download Chrome or Firefox or view our browser tips. The sequence then goes through a series of acquisition steps to generate four fundamental curves which are then post-processed to calculate crosstalk.
Sound System Equipment — Part 7: First, a pink noise stimulus is played from the noise 660268 and recorded by the unoccluded ears. Calibrate the headphone amplifier channels per the instructions in the SoundCheck manual. If the answer is No, the sequence jumps to post-processing steps which calculate passive attenuation and the final display step. The sequence uses a stepped sine stimulus to measure frequency response, THD and impedance, a composite signal of 70 Hz and Hz with an amplitude ratio of 4: It then enters a loop which will run 5 times.
The data from each loop iteration is displayed as it is acquired. A series of post processing steps calculates the attenuation curves, their average values and shows them on the final display.
Learn more about the cookies we use and how to change your settings. This value is converted to dBV and used to calculate the IM and difference frequency stimulus levels. The sequence prompts the operator to enter the rated voltage and rated impedance of the DUT. The sequence first plays a stepped sine through both channels of the DUT and captures the sound radiation from the DUT using 2 reference mics.
IEC Headphone Test Sequences – Listen, Inc.
The content you have requested is available only to registered visitors. Headphones and earphones Status: In order to add these Signal Paths to your System Calibration or relink to existing Signal Paths, you should open each of the sequences individually and, if prompted, add or relink Paths to your System Calibration. Noise speakers are set up adjacent to the HATS left and right ears.